These engines ought to have higher flow heads and cams for the Mikuni carb to be compatible. 8) Mikuni TMX 38-27-K Series 38mm Bore. This fits two-stroke off-road racing and Motocross uses. It features the radial flat side throttle design for the valve. This works well to improve throttle response. Carburettor Float Heights (MM) Carburettor Descriptions Float Height (mm) CRS All CR Smoothbores 14 FCR All FCR Carbs 9 PE20 PE20 19 PE22 PE22 19 PE24 PE24 19 PE38 PE38 22.5 PJ PJ 16 PWK28 PWK28 19 PWK33 PWK33 19 PWK35 PWK35 16 PWK35 A/S PWK35 A/S 16 PWK36 PWK36 16 PWK38 PWK38 16 PWK38 Read More ». Mikuni TMX 38 Float Height Tool. Click to Buy on eBay. Before you begin, please be sure to have your bike’s manual or the carburetor’s manual handy. Follow the directions that describe how to check and adjust the float height. Remove the carburetor from the bike. We recommend thoroughly cleaning the bike, especially around the carb. TM33 Carb Parts; TM36-68 Carb. TM36-68 Carb Parts; TM40-6 Carb. HS40 (TM40-6) Carb Parts; TM42 Carb. TM42 Carb Parts; TM45 Carb. TM45 Carb Parts; TM48 Carbs; TM Flatslide Carbs (Non Accel Pump) TM24 Carb. TM24 Parts; TM28 Carb. TM28 Parts; TM32 Carb. TM32 Parts; TM34 Carb. TM34 Parts; TM36 Carb. TM36 Parts; TM38 Carb. TM38 Parts; TMX.
#1
Before you begin, please be sure to have your bike’s manual or the carburetor’s manual handy. Follow the directions that describe how to check and adjust the float height.
#2
![Mikuni tm38 manual Mikuni tm38 manual](/uploads/1/2/4/6/124606807/684848281.jpg)
Remove the carburetor from the bike. We recommend thoroughly cleaning the bike, especially around the carb before removing it.
#3
Xvid player for mac. Remove the float bowl from the carburetor by removing the 3 screws.
#4
Install the tools as shown in the image using two of the float bowl machine screws. The screws need to be just tight enough to stop the tool from moving around. Do not over-tighten the screws or you will crack the plastic tool.
Note: The actual color of the product is black. It is no longer available in orange.
Note: The actual color of the product is black. It is no longer available in orange.
#5
Mikuni Tm 38 Carb Tuning
Position/rotate the carburetor to depress the needle as described in your manual. We recommend using a hobby vise to hold the carb in position. Be sure not to over-tighten the vise and bend or break the carburetor.
Mikuni Tmx38
#6
Hold a set of digital calipers on the top surface of the tool so the depth rod can protrude through the hole in the tool.
#7
Carefully move the caliper’s depth rod down until the end of the rod is making contact with the float.
While doing this, keep the edge of the calipers lightly and squarely resting on the top surface of the tool. This will ensure an accurate measurement.
While doing this, keep the edge of the calipers lightly and squarely resting on the top surface of the tool. This will ensure an accurate measurement.
#8
Take note of the reading on your calipers (in mm).
Subtract 17mm from your reading, this is the current float height.
Mikuni Tmx Carb
Example: If your calipers are reading 8.05mm, your float height is 8.95mm.
The calculation is: 17mm – 8.05mm = 8.95mm
Mikuni Tmx 38 Carburetor Manual Diagram
#9
Repeat for the other side. We recommend checking the height of both floats to ensure the float assembly is not bent.
#10
Mikuni Tm38 Manual
Adjust the float height according to your manual and recheck the height by following the procedures above.
Mikuni Tmx 38 Carburetor Manual Pdf
If you have a 3D printer, you can download the model at the link below.